Hostname: page-component-586b7cd67f-t8hqh Total loading time: 0 Render date: 2024-11-28T17:56:40.675Z Has data issue: false hasContentIssue false
  • English
  • Français

Advanced Ceramics Sintering Using High-Power Millimeter-Wave Radiation

Published online by Cambridge University Press:  10 February 2011

Y. Setsuhara ,
M. Kamai ,
S. Kinoshita ,
N. Abe ,
S. Miyake  and
T. Saji
Y. Setsuhara
Affiliation:
Welding Research Institute, Osaka University, Osaka, Japan, [email protected]
M. Kamai
Affiliation:
Welding Research Institute, Osaka University, Osaka, Japan, [email protected]
S. Kinoshita
Affiliation:
Welding Research Institute, Osaka University, Osaka, Japan, [email protected]
N. Abe
Affiliation:
Welding Research Institute, Osaka University, Osaka, Japan, [email protected]
S. Miyake
Affiliation:
Welding Research Institute, Osaka University, Osaka, Japan, [email protected]
T. Saji
Affiliation:
Fujidempa Kogyo Co., Ltd., Ibaraki, Japan
Get access

Abstract

The results of ceramics sintering experiments using high-power millimeter-wave radiation are reported. Sintering of silicon nitride with 5%Al2O3 and 5%Y2O3 was performed in a multi-mode applicator using a 10-kW 28-GHz gyrotron in CW operation. It was found that the silicon nitride samples sintered with 28 GHz radiation at 1650'C for 30 min reached to as high as theoretical density (TD), while the conventionally sintered samples at 1700°C for 60 min resulted in the density as low as 90% TD. Focusing experiments of millimeter-wave radiation from the high-power pulsed 60-GHz gyrotron have been performed using a quasi-optical antenna system (two-dimensional ellipso-parabolic focusing antenna system) to demonstrate the feasibility of the power density of as high as 100 kW/cm2. Typical heating characteristics using the focused beam were made clear for this system. It was found that the densification of yttria-stabilized zirconia (ZrO2-8mol%Y2O3) samples to as high as 97% TD was obtained from the sintering with focused 60 GHz beam in pulse operation with a 10-ms pulse duration at a 0.5Hz repetition. The densification temperature for the zirconia could be lowered by 200°C than that expected conventionally.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 430: Symposium O – Microwave Processing of Materials V , 1996 , 533
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Sutton, W. H., Am. Ceram. Soc. Bull. 68 (2), 376 (1989).Google Scholar
2. Meek, T. T., Blake, R. D. and Petrovic, J. J., Ceram. Eng. Sci. Proc. 8, 861 (1987).Google Scholar
3. Janny, M. A. and Kimery, H. D., in Microwave Processing of Materals 11, edited by Snyder, W. B. Jr., Sutton, W. H., Iskander, M. F. and Johnson, D. L.(Mater. Res. Soc. Proc. 189, San Francisco, CA, 1990) pp.2 15–22 7.Google Scholar
4. Janney, M. A., Calhoun, C. L., and Kimrey, H. D., I. Am. Ceram. Soc. 75 (2), 341 (1992).Google Scholar
5. Bykov, Yu. V., 'denberg, A. F. L. Gol and Flyagin, V. A., in Microwave Processing of Materals 11, edited by Snyder, W. B. Jr., Sutton, W. H., Iskander, M. F. and Johnson, D. L. (Mater. Res. mSoc. Proc. 189, San Francisco, CA, 1990) pp.4 1–4 2.Google Scholar
6. Setsuhara, Y., Tabata, Y., Ohnishi, R. and Miyake, S., Trans. JWRI 21, 181 (1992).Google Scholar
7. Saji, T., New Ceramics 8, 21 (1995) (in Japanese).Google Scholar
8. Miyake, S., Nakajima, O. Wada, M., Idehara, T. and Brand, G. F., Int. J. Electronics 70, 979 (1991).Google Scholar
9. Wada, O.and Nakajima, M., Space Power 6, 3 (1987).Google Scholar