Hostname: page-component-586b7cd67f-t8hqh Total loading time: 0 Render date: 2024-11-24T18:58:40.508Z Has data issue: false hasContentIssue false
  • English
  • Français

Suitability of various complex hydrides for foaming aluminum alloys

Published online by Cambridge University Press:  10 May 2013

Paul H. Kamm ,
Francisco García-Moreno ,
Catalina Jiménez  and
John Banhart
Paul H. Kamm
Affiliation:
Structure and Properties of Materials, Technical University Berlin, 10623 Berlin, Germany
Francisco García-Moreno*
Affiliation:
Structure and Properties of Materials, Technical University Berlin, 10623 Berlin, Germany; and Institute of Applied Materials, Helmholtz Centre Berlin, 14109 Berlin, Germany
Catalina Jiménez
Affiliation:
Structure and Properties of Materials, Technical University Berlin, 10623 Berlin, Germany; and Institute of Applied Materials, Helmholtz Centre Berlin, 14109 Berlin, Germany
John Banhart
Affiliation:
Structure and Properties of Materials, Technical University Berlin, 10623 Berlin, Germany; and Institute of Applied Materials, Helmholtz Centre Berlin, 14109 Berlin, Germany
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Some hydrides that could replace TiH2 as the hitherto most suitable blowing agent for foaming aluminum alloys were investigated. Hydrides taken from the group MBH4 (M = Li, Na, K) and LiAlH4 were selected since these have not been studied in the past although their decomposition characteristics appear to be suitable. Foamable precursors of alloy AlSi8Mg4 were manufactured by pressing blends of metal and blowing agent powders. Powders, precursors and precursor filings were studied by mass spectrometry to obtain the hydrogen desorption profile. Foaming experiments were conducted with simultaneous x-ray radiographic monitoring. Two Li-containing blowing agents were found to perform well and can be considered alternatives to TiH2.

Type
Invited Feature Paper
Information
Journal of Materials Research , Volume 28 , Issue 17: Focus Issue: Advances in the Synthesis, Characterization, and Properties of Bulk Porous Materials , 14 September 2013 , pp. 2436 - 2443
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Banhart, J.: Manufacturing routes for metallic foams JOM 52(12), 22 (2000).CrossRefGoogle Scholar
Matijasevic, B. and Banhart, J.: Improvement of aluminium foam technology by tailoring of blowing agent. Scr. Mater. 54(4), 503 (2006).CrossRefGoogle Scholar
Gergely, V. and Clyne, B.: The FORMGRIP process: Foaming of reinforced metals by gas release in precursors. Adv. Eng. Mater. 2(4), 175 (2000).3.0.CO;2-W>CrossRefGoogle Scholar
Kennedy, A.R.: The effect of TiH2 heat treatment on gas release and foaming in Al-TiH2 preforms. Scr. Mater. 47(11), 763 (2002).CrossRefGoogle Scholar
Lehmhus, D. and Rausch, G.: Tailoring titanium hydride decomposition kinetics by annealing in various atmospheres. Adv. Eng. Mater. 6(5), 313 (2004).CrossRefGoogle Scholar
Matijasevic-Lux, B., Banhart, J., Fiechter, S., Görke, O., and Wanderka, N.: Modification of titanium hydride for improved aluminium foam manufacture. Acta Mater. 54(7), 1887 (2006).CrossRefGoogle Scholar
Jiménez, C., Garcia-Moreno, F., Pfretzschner, B., Klaus, M., Wollgarten, M., Zizak, I., Schumacher, G., Tovar, M., and Banhart, J.: Decomposition of TiH2 studied in situ by synchrotron X-ray and neutron diffraction. Acta Mater. 59(16), 6318 (2011).CrossRefGoogle Scholar
Jiménez, C., Garcia-Moreno, F., Rack, A., Tucoulou, R., Klaus, M., Pfretzschner, B., Rack, T., Cloetens, P., and Banhart, J.: Partial decomposition of TiH2 studied in situ by energy-dispersive diffraction and ex situ by diffraction microtomography of hard X-ray synchrotron radiation. Scr. Mater. 66(10), 757 (2012).CrossRefGoogle Scholar
Nakamura, T., Gnyloskurenko, S.V., Sakamoto, K., Byakova, A.V., and Ishikawa, R.: Development of new foaming agent for metal foam. Mater. Trans. 43(5), 1191 (2002).CrossRefGoogle Scholar
Gnyloskurenko, S.V., Byakova, A.V., Sirko, A.I., Dudnyk, A.O., Milman, Y.V., and Nakamura, T.: Advanced structure and deformation pattern of Al based alloys foamed with calcium carbonate agent, in Porous Metals and Metallic Foams: Metfoam 2007, edited by Lefebvre, L.P., Banhart, J., and Dunand, D.C. (DEStech, Montreal, Canada, 2008), p. 399.Google Scholar
Yang, D.H., Hur, B.Y., and Yang, S.R.: Study on fabrication and foaming mechanism of Mg foam using CaCO3 as blowing agent. J. Alloys Compd. 461(1–2), 221 (2008).CrossRefGoogle Scholar
Li, D., Li, J., Li, T., Sun, T., Zhang, X., and Yao, G.: Preparation and characterization of aluminum foams with ZrH2 as foaming agent. Trans. Nonferrous Met. Soc. China 21(2), 346 (2011).CrossRefGoogle Scholar
Körner, C., Hirschmann, M., Bräutigam, V., and Singer, R.F.: Endogenous particle stabilization during magnesium integral foam production. Adv. Eng. Mater. 6(6), 385 (2004).CrossRefGoogle Scholar
Mondal, D.P., Goel, M.D., and Das, S.: Effect of strain rate and relative density on compressive deformation behaviour of closed cell aluminum–fly ash composite foam. Mater. Des. 30(4), 1268 (2009).CrossRefGoogle Scholar
Au, M., Spencer, W., Jurgensen, A., and Zeigler, C.: Hydrogen storage properties of modified lithium borohydrides. J. Alloys Compd. 462(1–2), 303 (2008).CrossRefGoogle Scholar
Lee, J.Y., Lee, Y-S., Suh, J-Y., Shim, J-H., and Cho, Y.W.: Metal halide doped metal borohydrides for hydrogen storage: The case of Ca(BH4)2–CaX2 (X=F, Cl) mixture. J. Alloys Compd. 506(2), 721 (2010).CrossRefGoogle Scholar
Rönnebro, E.: Development of group II borohydrides as hydrogen storage materials. Curr. Opin. Solid State Mater. Sci. 15(2), 44 (2011).CrossRefGoogle Scholar
Senoh, H., Siroma, Z., Fujiwara, N., and Yasuda, K.: A fundamental study on electrochemical hydrogen generation from borohydrides. J. Power Sources 185(1), 1 (2008).CrossRefGoogle Scholar
Li, H.W., Yan, Y.G., Orimo, S., Zuttel, A., and Jensen, C.M.: Recent progress in metal borohydrides for hydrogen storage. Energies 4(1), 185 (2011).CrossRefGoogle Scholar
Fakioglu, E., Yurum, Y., and Veziroglu, T.N.: A review of hydrogen storage systems based on boron and its compounds. Int. J. Hydrogen Energy 29(13), 1371 (2004).CrossRefGoogle Scholar
Chandra, D., Reilly, J.J., and Chellappa, R.: Metal hydrides for vehicular applications: The state of the art. JOM 58(2), 26 (2006).CrossRefGoogle Scholar
Helwig, H.M., Hiller, S., Garcia-Moreno, F., and Banhart, J.: Influence of compaction conditions on the foamability of AlSi8Mg4 alloy. Metall. Mater. Trans. B 40(5), 755 (2009).CrossRefGoogle Scholar
Rodriguez-Perez, M.A., Solorzano, E., De Saja, J.A., and Garcia-Moreno, F.: The time-uncoupled aluminium free-expansion: Intrinsic anisotropy by foaming under conventional conditions, in Porous Metals and Metallic Foams: Metfoam 2007, edited by Lefebvre, L.P., Banhart, J., and Dunand, D.C. (DEStech, Montreal, Canada, 2008), p. 75.Google Scholar
Jiménez, C., García-Moreno, F., Banhart, J., and Zehl, G.: Effect of relative humidity on pressure-induced foaming (PIF) of aluminium-based precursors, in Porous Metals and Metallic Foams: Metfoam 2007, edited by Lefebvre, L-P., Banhart, J., and Dunand, D. (DEStech, Montréal, Canada, 2008), p. 59.Google Scholar
Jiménez, C., Garcia-Moreno, F., Mukherjee, M., Goerke, O., and Banhart, J.: Improvement of aluminium foaming by powder consolidation under vacuum. Scr. Mater. 61(5), 552 (2009).CrossRefGoogle Scholar
Helwig, H.M., Garcia-Moreno, F., and Banhart, J.: A study of Mg and Cu additions on the foaming behaviour of Al-Si alloys. J. Mater. Sci. 46(15), 5227 (2011).CrossRefGoogle Scholar
Garcia-Moreno, F., Fromme, M., and Banhart, J.: Real-time X-ray radioscopy on metallic foams using a compact micro-focus source. Adv. Eng. Mater. 6(6), 416 (2004).CrossRefGoogle Scholar
van der Pauw, I.J.: A method of measuring the resistivity and Hall coefficient on lamellae of arbitrary shape. Philips Tech. Rev. 20, 5 (1958).Google Scholar
Partridge, P.G.: Oxidation of aluminium lithium alloys in the solid and liquid states. Int. Mater. Rev. 35(1), 37 (1990).CrossRefGoogle Scholar
Shirzadi, A.A., Assadi, H., and Wallach, E.R.: Interface evolution and bond strength when diffusion bonding materials with stable oxide films. Surf. Interface Anal. 31(7), 609 (2001).CrossRefGoogle Scholar
Ureña, A., de Salazar, J.M.G., Quinones, J., Merino, S., and Martin, J.J.: Diffusion bonding of an aluminium-lithium alloy (AA8090) using aluminium-copper alloy interlayers .1. Microstructure. J. Mater. Sci. 31(3), 807 (1996).CrossRefGoogle Scholar
Züttel, A., Wenger, P., Rentsch, S., Sudan, P., Mauron, P., and Emmenegger, C.: LiBH4 a new hydrogen storage material. J. Power Sources 118(1–2), 1 (2003).CrossRefGoogle Scholar
Jiménez, C., Garcia-Moreno, F., Pfretzschner, B., Kamm, P.H., Neu, T.R., Klaus, M., Genzel, C., Hilger, A., Manke, I., and Banhart, J.: Metal foaming studied in Situ by energy dispersive X-ray diffraction of synchrotron radiation, X-ray radioscopy, and optical expandometry. Adv. Eng. Mater. 15(3), 141 (2013).CrossRefGoogle Scholar
Campana, F. and Pilone, D.: Effect of wall microstructure and morphometric parameters on the crush behaviour of Al alloy foams. Mater. Sci. Eng., A 479(1–2), 58 (2008).CrossRefGoogle Scholar
Garcia-Moreno, F. and Banhart, J.: Foaming of blowing agent-free aluminium powder compacts. Colloids Surf., A 309(1–3), 264 (2007).CrossRefGoogle Scholar
Stanzick, H., Duarte, I., and Banhart, J.: Foaming process of aluminum. Materialwiss. Werkstofftech. 31(6), 409 (2000).3.0.CO;2-O>CrossRefGoogle Scholar
Emadi, D., Gruzleski, J.E., and Toguri, J.M.: The effect of Na and Sr modification on surface tension and volumetric shrinkage of A356 alloy and their influence on porosity formation. Metall. Trans. B 24(6), 1055 (1993).CrossRefGoogle Scholar