Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-01T07:03:56.175Z Has data issue: false hasContentIssue false
  • English
  • Français

The management of measurement processes – key to robust andcost optimal production of high quality products

Published online by Cambridge University Press:  03 May 2010

R. Schmitt ,
J. Lose  and
M. Harding
Get access

Abstract

Today’s production industry has to face considerable challenges. Decentralised andcross-linked production processes lead to a highly complex production control and aworldwide financial crisis causes drastic movements in demand. To succeed in businessunder these conditions, production needs to be transparent. One key factor to increasetransparency is the management of measurement processes. The management of measurementprocesses focuses not only on the measurement process itself that enables the decision onthe conformity of a measurand but, beyond that, it considers the acquisition of knowledgethroughout the production process, its validation, processing and feedback into theprocess chain. With proof of measurement process capability, the determination of theoptimal trade-off among measuring and production process, the adjustment of optimalworking points and tolerances is achieved. The management of measurement processes allowsobtaining a maximum benefit from metrology under the consideration of technical,organisational and economical boundary conditions.

Keywords

Management of measurement processestransparencyvalidationcapabilitytolerance design
Type
Research Article
Information
International Journal of Metrology and Quality Engineering , Volume 1 , Issue 1 , 2010 , pp. 1 - 6
Copyright
© EDP Sciences 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Bunday, B. et al., Value-Added Metrology, IEEE Trans. Semicond. Manuf. 20, 266 (2007) CrossRefGoogle Scholar
Kunzmann, H., Pfeifer, T., Schmitt, R., Schwenke, H., Weckenmann, A., Productive Metrology – Adding Value to Manufacture, Ann. CIRP 54, 691 (2005) CrossRefGoogle Scholar
W. Thomson, Electrical Units of Measurement, Popular Lecture an Addresses, Vol. I (Macmillan, London, 1883), p. 73
Aamodt, A., Nygård, M., Data Knowledge Eng. 16, 191 (1995) CrossRef
Shannon, C., A Mathematical Theory of Communication, Bell Syst. Tech. J. 27, 379, 623 (1948) CrossRefGoogle Scholar
F. de Saussure, Grundfragen der allgemeinen Sprachwissenschaft, 3rd edn. (De Gruyter, 2001)
K. North, Wissensorientierte Unternehmensführung – Wertschöpfung durch Wissen, 2nd edn. (Gabler, 1999)
J.-R. Ohm, H. Lüke, Signalübertragung, 7th edn. (Springer, 2005)
A. Picot, R. Reichwald, R. Wigang, Die grenzenlose Unternehmung – Information, Organisation und Management, 5th edn. (Gabler, 2003)
R. Schmitt, B. Damm, P. Hafner, Machine-Vision-Based Automated Tool Wear Inspection System, in Proceedings of the 18th IMEKO TC2 Symposium (2008), pp. 1–6
T. Pfeifer, Production Metrology (2002), pp. 1–2
T. Pfeifer et al., Measuring flank tool wear on cutting tools with machine vision – a case solution, in 9th IEEE Conference on Mechatronics and Machine Vision in Practice (2002), pp. 169–175
G. Schuh et al., Intelligent Maintenance – Potentiale zustandsorientierter Instandhaltung (2005), p. 6
H. Braeunlich, Blecheinzugsregelung beim Tiefziehen mit Niederhalter – ein Beitrag zur Erhöhung der Prozessstabilität (Verlag Wissenschaftliches Scripten, 2002), pp. 19–20
R. Ofen et al., Qualitätsdatenaustauschformat der Automobilindustrie AQDEF, workgroup paper version 2.0.1, http://www.q-das.de/fileadmin/files2/datafomat/Specification_AQDEF_V3-0.pdf, 2008
G. Schuh et al., Designing services based on ‘intelligent’ press-die-systems, Advances in Life Cycle Engineering for Sustainable Manufacturing Businesses, in Proceedings of the 14th CIRP Conference on Life Cycle Engineering (2007), pp. 201–205
R. Schmitt et al., Anlage, Werkzeug, Betreiber – Produktionseffizienz durch Anwenderorientierung, Wettb- ewerbsfaktor Produktionstechnik Aachener Perspekti- ven, in Proceedings of the AWK 2008, pp. 391–417
R. Brinkmann, Measurement System Analysis (MSA) und Prüfprozesseignung (Richtlinie VDA5), in VDI Berichte 1913 (VDI-Verlag, 2005), pp. 63–71
DINV ENV 13005, Guide to the Expression of Uncertainty in Measurement, German Version ENV 13005 (1999)
Measurement System Analysis (MSA), 3rd edn. (2002)
VDA 5 - Qualitätsmanagement in der Automobilindustrie, Prüfprozesseignung, 1st edn. (Verband der Automobilin- dustrie, 2003)
DIN ISO/TS15330-3, Geometrische Produktspezifikation (GPS) – Verfahren zur Ermittlung der Messunsicherheit von Koordinatenmessgeräten (KMG) – Teil 3: Anwendung von kalibrierten Werkstücken oder Normalen (2008)
JCGM 101:2008, Evaluation of measurement data – Supplement 1 to the “Guide to the expression of uncertainty in measurement” – Propagation of distributions using a Monte Carlo method (2008)