The Tibetan Plateau interior area (TPIA), often termed the Qangtang Plateau, is distinguished by many dome-like mountains higher than 6000 ma.s.l. These mountains provide favourable conditions for the development of ice caps and glaciers of extreme continental/subpolar type. According to historical topographic maps (1959–80) and recent Landsat images (2004–11), continuous retreat was observed and the glacierized part of this area decreased by 9.5% (0.27% a–1) with respect to the total glacier area of 8036.4 km2 in the 1970s. Glaciers in the Zhari Namco basin have experienced the highest area shrinkage, with a reduction rate of 0.72% a–1, while the smallest reduction occurred in Bangong Co (0.12% a–1) and Dogai Coying basins (0.11% a–1). A regional gradient of area loss was found, with a larger decrease in the south and a smaller decrease in the north of the plateau. Comparisons indicate glaciers have experienced smaller shrinkage in the TPIA than in surrounding regions. Glacier shrinkage in the TPIA is mainly attributed to an increase in air temperature, while precipitation, glacier size and positive difference of glaciation also played an important role.

Continuous good-quality deep ice cores provide excellent scientific data with which to reconstruct a past climate record for >800 ka. At depths starting from ∼100m using an electromechanical drill, a drilling liquid is essential for successful recovery of the very high-quality ice cores demanded by modern scientific analysis techniques (e.g. continuous flow analysis). Finding a suitable drill fluid for use at deep ice-coring drill sites is not an easy task. Temperatures vary greatly not just from site to site, but also at a site where the average mean temperature from surface to bedrock can vary from –55°C to –2.75°C. In the past 60 years, many fluids have been used, with varying degrees of success, but for various reasons are either unavailable, are now considered unsafe and dangerous or are too environmentally damaging to be permitted. Here we report on our pre-season investigation into possible candidate drill fluids, with specific information concerning ESTISOL™ 240 and COASOL™, the rationale behind the redesign of our drill successfully used at NorthGRIP, Greenland, and EPICA DML, Antarctica, the knock-on effect of those changes, and our field experience in Greenland at Flade Isblink in 2006 and at NEEM in 2009–10.

This paper provides the results of semi-distributed positive degree-day (PDD) modelling for a glacierized river basin in Nepal. The main objective is to estimate the present and future discharge from the glacierized Langtang River basin using a PDD model (PDDM). The PDDM is calibrated for the period 1993–98 and is validated for the period 1999–2006 with Nash–Sutcliffe values of 0.85 and 0.80, respectively. Furthermore, the projected precipitation and temperature data from 2010 to 2050 are obtained from the Bjerknes Centre for Climate Research, Norway, for the representative concentration pathway 4.5 (RCP4.5) scenario. The Weather Research and Forecasting regional climate model is used to downscale the data from the Norwegian Earth System Model general circulation model. Projected discharge shows no significant trend, but in the future during the pre-monsoon period, discharge will be high and the peak discharge will be in July whereas it is in August at present. The contribution of snow and ice melt from glaciers and snowmelt from rocks and vegetation will decrease in the future: in 2040–50 it will be just 50% of the total discharge. The PDDM is sensitive to monthly average temperature, as a 2°C temperature increase will increase the discharge by 31.9%. Changes in glacier area are less sensitive, as glacier area decreases of 25% and 50% result in a change in the total discharge of –5.7% and –11.4%, respectively.

In response to the ‘oldest ice’ challenge initiated by the International Partnerships in Ice Core Sciences (IPICS), new rapid-access drilling technologies through glacier ice need to be developed. These will provide the information needed to qualify potential sites on the Antarctic ice sheet where the deepest section could include ice that is >1Ma old and still in good stratigraphic order. Identifying a suitable site will be a prerequisite for deploying a multi-year deep ice-core drilling operation to elucidate the cause and mechanisms of the mid-Pleistocene transition from 40 ka glacial–interglacial cycles to 100 ka cycles. As part of the ICE&LASERS/SUBGLACIOR projects, we have designed an innovative probe, SUBGLACIOR, with the aim of perforating the ice sheet down to the bedrock in a single season and continuously measuring in situ the isotopic composition of the melted water and the methane concentration in trapped gases. Here we present the general concept of the probe, as well as the various technological solutions that we have favored so far to reach this goal.

Accelerating loss of glacial mass caused by rising global temperatures has significant implications. The global cycle of the greenhouse gas CO2 is also associated with mineral weathering and glaciation. In glaciated areas, most estimates of atmospheric CO2 consumption are confined to chemical ionic mass balance or analog modeling methods. We applied the gradient method to the surface of Koxkar glacier, western Tien Shan, China, for a 5 month period during 2012. The overall net glacier-system CO2 exchange (NGE) rate was measured as -0.05 and -0.07mmol m–2 s–1 for regions of exposed ice and supraglacial moraine, respectively. This suggests that atmospheric CO2 drawdown may occur during ice melting because of consumption of H+ by CO2 hydrolysis that occurs in solutions. Using the degree-day model to calculate glacier ablation in bare-ice regions and considering characteristics of the NGE rate in the supraglacial debris region with the support of GIS, the daily NGE rate was estimated to be -1.23 ± 0.17μmmol m–2 d–1 between Julian days 125 and 268 of 2012. These findings present a new approach for modeling the dynamics of glacial CO2 sinks undergoing melting, and develop an understanding of the mechanism of atmospheric CO2 exchange.

The British Antarctic Survey, in collaboration with Laboratoire de Glaciologie et Géophysique de l’Environnement, has in recent years successfully drilled to bedrock on three remote sites around the Antarctic Peninsula. Based on the experience from the multi-season project at Berkner Island (948m depth, 2002–05) we optimized the drill set-up to better suit two subsequent single-season projects at James Ross Island (363m depth, 2008) and Fletcher Promontory (654m depth, 2012). The adaptations, as well as the reasons for them, are discussed in detail and include a drill tent set-up without a trench; drilling without a borehole casing with a relatively low fluid column height; and using a shorter drill. These optimizations were aimed at reducing cargo loads and installation time while maintaining good core quality, productivity and a safe working environment. In addition, we introduce a number of innovations, ranging from a new lightweight cable tensioning device and drill-head design to core storage and protection trays. To minimize the environmental impact, all the drill fluid was successfully recovered at both sites and we describe and evaluate this operation.

Water level fluctuations of inland lakes are related to regional-scale climate changes, and reflect variations in evaporation, precipitation and glacier meltwater flowing into the lake area in its catchment. In this paper, Ice, Cloud and land Elevation Satellite (ICESat) altimeter data and Landsat imagery (2002-09) are used to estimate Nam Co lake (Nyainqentanglha range, Tibetan Plateau) water elevation changes during 2002-09. In 2003 Nam Co lake covered an area of ~1998.8 ± 4.2 km2 and was situated at 4723 m a.s.l. Over such inland water bodies, ICESat altimeter data offer both wide coverage and spatial and temporal accuracy. We combine remote-sensing and GIS technology to map and reconstruct lake area and increased volume changes during a 7 year time series. Nam Co lake water level increased by 2.4±0.12m (0.33ma–1) between 23 February 2003 and 1 October 2009, and lake volume increased by 4.9 ±0.5 km3. In the past 7 years, Nam Co lake area has increased from 1998.78 ±5.4 to 2023.8 ±3.4 km2, the glacier-covered area has decreased from 832.34 to 821.0 km2 and the drainage basin area has decreased from 201.1 ±4.2 to 196.1 ±2.3 km2. However, the most spectacular feature is the continual water level rise from 2003 to 2009 without an obvious associated increase in precipitation. Based on digital elevation models (DEMs) from Shuttle Radar Topography Mission (SRTM) DEM data and corrected ICESat elevation data, significant changes to glacier mass balance in the western Nyainqentanglha mountains are indicated. Nyainqentanglha mountain glacier surface elevations decreased by 8.39 ± 0.45 m during 2003-09. Over the same period, at least 1.01 km3 of glacial meltwater flowed into Nam Co lake, assuming a glacial runoff coefficient of 0.6. The mean glacier mass-balance value is -490mmw.e. over the corresponding period, indicating that glacier meltwater in the catchment contributes to lake level rise. The contribution rate of glacial meltwater to lake water volume rise is 20.75%. The temporal lake level fluctuation correlates with temperature variations over the same time span.

Characterized by fast movement, low surface slope and grounding below sea level, Pine Island Glacier (PIG) plays an important role in the stability of the West Antarctic ice sheet. In previous work, we reported that the spatial distribution of 1995–2003 surface lowering in PIG suggests an attribution of changes to an internally forced process in the glacier. Other work associates changes in PIG entirely with processes in its ice shelf. Here time series of maps of surface elevation change in PIG and its ice shelf are derived from geostatistical analysis of ICESat GLAS and ERS-1 radar altimeter data. Based on spatio-temporal analysis of 1995–2007 elevation change, we discuss indications of processes that initiate from changes in the ice shelf versus processes that start internally in the glacier. Thinning rates continued to increase after 2003, regionally to >15 m a–1. The initiation of acceleration occurred in the interior of the ice stream, while in later years largest elevation loss was driven by changes in the ice shelf and upward propagation. By 2006, the region of thinning had expanded up-glacier beyond the initial areas of surface lowering to 100 km above the hinge line. More than one process causes dynamically complex changes in PIG.

The Enceladus Explorer project is a preparatory study for a future space mission to Saturn’s moon, Enceladus. Its ultimate goal is to probe liquid-water pockets below the ice surface of Enceladus for signatures of life. A probe could be based on the IceMole concept, which melts curved trajectories through the ice. In the Enceladus Explorer project, a specialized IceMole probe for a terrestrial test scenario is in development. The goal of this exploratory study is to probe water from a liquid crevasse close to Blood Falls at Taylor Glacier, Antarctica. To navigate such a probe it is essential to be able to determine its position and monitor its trajectory. Part of the navigation system is the in-ice acoustic positioning system. For this, the head of the IceMole is equipped with acoustic sensors, which receive signals from synchronized acoustic emitters situated at the ice surface. Based on the measured propagation times, the speed of sound in ice and the positions of the emitters at the surface, the position of the IceMole can be determined by trilateration techniques. Here we present the developed acoustic positioning system, which is designed to track the in-ice melting probe up to distances of 100 m in glacier ice. Results from full-system tests in water and a first field test on Morteratschgletscher, Switzerland, are discussed.

A drill liquid is essential for the purpose of recovering good-quality scientifically useful ice cores at intermediate to deep depths, i.e. >∼100 m. The pressure produced by the liquid helps to eliminate the detrimental effects of the abrupt release of isostatic pressure in the ice during the drilling process, prevents consequential fractures within the ice core, and is essential to produce an even distribution of hydrostatic pressure to balance the ice isostatic pressure and so minimize borehole deformation. To perform these tasks, while minimizing risks to health and the environment, the liquid needs to exhibit specific physical, chemical and biological characteristics. Here we report on two promising candidate drill liquids, ESTISOL™ 140 and ESTISOL™ 165, for use in the extreme conditions found within the ice sheets of Greenland and Antarctica, where the temperature can range from close to 0°C to below −57°C and pressures can exceed 40 MPa. From both the manufacturer’s data and our laboratory tests and observations we report on the physical, chemical and biological characteristics that both liquids exhibit. We also report on how one of the candidates was field-tested on the Greenland ice sheet and the East Antarctic high plateau.

Based on the results of geochemical and glaciological investigations in snow pits and shallow cores, regional stack series of air temperature in central Antarctica (in the southern part of Vostok Subglacial Lake) were obtained, covering the last 350 years. It is shown that this parameter varied quasi-periodically with a wavelength of 30–50 years. The correlation of the newly obtained record with the circulation indices of the Southern Hemisphere (SH) shows that the central Antarctic climate is mainly governed by the type of circulation in the SH: under conditions of zonal circulation, negative anomalies of temperature and precipitation rate are observed, whereas the sign of the anomalies is positive during meridional circulation. In the 1970s the sign of the relationship between many climatic parameters changed, which is likely related to the rearrangement of the climatic system of the SH. The data suggest that during the past 350 years such events have taken place at least five times. The stable water isotope content of the central Antarctic snow is governed by the summer temperature rather than the mean annual temperature, which is interpreted as the influence of ‘postdepositional’ effects.

Several recent projects associated with the IPICS (International Partnerships in Ice Core Sciences) 2k array have demanded the recovery of ice core to depths in excess of several hundred metres (e.g. Flade Isblink, Greenland (2006), Aurora Basin, Antarctica (2008/09), NEEM, Greenland (2011), Aurora Basin North (2013/14) and Renland ice cap, Greenland (2015)). These projects require that the overall system weight is low, that the ability to set up and operate are within the limitations of a small-camp environment and that the overall logistical and transportation costs are kept to a minimum. Using these criteria, a new drilling system capable of drilling >400m depth was seen as a useful future development. Here we report on a new intermediate-depth drilling system designed to recover high-quality 98 mm diameter ice cores from close to surface down to depths of 1000 m by two or more operators in a small deep-field camp environment. The total weight of the system on the snow surface is ∼490 kg, of which the intermediate-depth winch is the single heaviest component at 305 kg with 1000 m of cable.

A new, clean, hot-water drill system (HWDS) was developed by the Science Management Office, University of Nebraska-Lincoln, for use in the Whillans Ice Stream Subglacial Access Research Drilling (WISSARD) project to gain access to Subglacial Lake Whillans beneath ∼800 m of ice in West Antarctica. One primary borehole was drilled into the basal ice environment of Subglacial Lake Whillans during the initial field season in 2012/13. This paper describes the process of designing, fabricating, assembling, shipping, testing, commissioning and traversing the WISSARD HWDS leading up to the first scientific use of the system.

Successful hot-water drilling in the Antarctic is predicated on utilization of the abundant water supply available in the form of the Antarctic ice sheet. For WISSARD (Whillans Ice Stream Subglacial Access Research Drilling) field operations, a snowmelting system was developed that could adequately provide water for a 1000 kW hot-water drill. The system employs ∼100 kW of waste heat from a 225 kW generator to melt snow for initial water (known as seed water) to prime the drill’s high-pressure pumps and water heaters; once the water heaters can be engaged in snowmelting, enough water can be supplied directly to the WISSARD drill to successfully melt a 40 cm diameter hole through 800 m of ice.

The WISSARD (Whillans Ice Stream Subglacial Access Research Drilling) traversable hot-water drill system was designed to create various-diameter ice boreholes to a depth of >800 m, with most major components being controllable from a single user interface. The drill control system operates four low-pressure pumps for water generation and circulation, two hot-water generation units containing a total of six diesel burner modules with integrated high-pressure pumps, three winches (one with independent level-wind motor), a four-motor linear traction drive, and a large number of analog and digital sensors to monitor system performance and cleanliness. Due to development time constraints the control system design focused on utilizing commercial off-the-shelf components, while being highly modular, easily expandable and rapidly deployable. Additional emphasis was placed on providing redundant manual operator controls and maintaining a low degree of system automation to avoid dependence on software control loops for first-season deployment. The result of this design paradigm was a control system that was taken from concept to full operation in <6 months, successfully performing in the field without insurmountable problems.

As part of the ICE&LASER/SUBGLACIOR projects, an innovative probe called SUBGLACIOR is developed with the aim of perforating the ice sheet down to depths of 3500 m in a single season and continuously measuring in situ the isotopic composition of the meltwater and the methane concentration in trapped gases. Ice chips generated by the electromechanical drilling will be removed from the borehole by circulating a drill fluid. The selection of this drill fluid is important as it will have a major impact on the performance and the environmental evaluation. A literature review of drilling liquids is carried out to select potential fluids for further detailed testing. The selected fluids are varying grades of silicone oils, known as linear polydimethylsiloxanes, and ESTISOL™ 140, an aliphatic ester. The requirements for this project are similar to those for other deep ice-core drilling projects but, due to the embedded analytical system and the speed of drilling, there are some specific considerations. Following extensive testing, we conclude that a silicone fluid with a kinematic viscosity of 3 mm2 s−1 (3 cSt) is ideally suitable and affordable. This evaluation provides new insights into the use of silicone oils as a drill fluid that are of use to the wider ice-core drilling community.

Ice coring of temperate and polythermal glaciers demonstrates some limitations of most electromechanical (EM) and thermal electric (TE) drills. Most TE drills are heavy, require a heavy power system, work slowly and cannot operate in boreholes going through the cold–temperate ice transition. Antifreeze thermal electric drills (ATED) are capable of operating in polar ice caps, polythermal and temperate glaciers, in boreholes filled with water and/or hydrophilic fluids. Performance of the ATED drill can be improved by using an open-top core barrel and low-power and narrow-kerf coring head. ATED-type drills can be modified for an open-top core barrel equipped with low-power coring head and include a new scheme for drilling-fluid circulation using two pumps. A small metering pump releases pure ethanol above the top of the drill, and a second pump enables circulation of the borehole fluid, an ethanol–water solution (EWS), above the kerf. Use of a narrow-kerf coring head reduces power requirements and makes it possible to design a lightweight drilling system that includes the EM and TE drills for shallow and intermediate-depth drilling.

Drilling the WDC06A borehole at the West Antarctic Ice Sheet (WAIS) Divide with the Deep Ice Sheet Coring (DISC) drill began in December 2007 and was successfully completed in December 2011 to a depth of 3405 m. The design and construction of a replicate coring system for use with the existing DISC drill began in 2010. In January 2012, the new replicate coring system was tested in the parent borehole at WAIS Divide. While a full deviation was not completed during the test period, much was learned about the mechanical, electrical and operational aspects of the system. Extensive testing and modifications were done over the northern/boreal summer to prepare the system for the upcoming and final season of the project. Further tuning of the system continued during the 2012/13 field season at WAIS Divide. This paper identifies the issues found with the system during the initial test season and discusses solutions, methods and testing done to arrive at an operational system.

More than 170 years ago, Louis Agassiz, one of the creators of glacial theory, made his first attempt to drill into the bed of Unteraargletscher, Swiss Alps. Since that time, various systems for thermal and mechanical drilling have been designed especially for boring into ice, and some conventional drill rigs been adopted for ice coring. Although contemporary ice-drilling knowledge and techniques are now familiar, there remain many problems to be solved by advanced modern technology. Specific challenges related to improving old drilling methods and developing new emerging technologies include: (1) identification of depth limitation of ‘dry’ drilling; (2) improvement of casing; (3) searching for the new environmentally friendly low-temperature drilling fluids; (4) reliable elimination of sticking drills; (5) improvement of core quality in the brittle zone; (6) additional core sampling from borehole walls after the core has been drilled; (7) obtaining oriented core; (8) designing automation drilling systems; (9) developing rapid-access drills. Possible ways of solving these problems are presented below.

In the frame of the SUBGLACIOR project, a new type of casing has been installed for testing during the 2013/14 austral summer season at Dome Concordia station, Antarctica. The SUBGLACIOR probe requires a full fluid column up to the surface, in order to circulate fluid for ice-chips recovery. This makes it essential that the casing is leak-tight through the porous firn column. We have evaluated existing solutions before opting to test a new method. This new system is made of polyethylene pipes which are welded together at the surface while the casing pipes are lowered into the reamed borehole. It is simple and lightweight and allows the casing to be installed quickly with optimum chance of being leak-tight. The installed casing has been tested both with compressed air and drilling fluids and has proven to work.